TDR 2000

¡@Feature¡@

  1. Size 00 probe for coaxial contact pin replacement.
  2. 18GHz Microwave switches and microwave cables assembly.
  3. ESD protection includes ionized fan and discharge before test function to prevent TDR meter from damage.
  4. GPIB interface.
  5. Windows 2000 menu driven software structure.
  6. Daily, monthly histogram reports produced by CPK calculation
¡@Dimension¡@
¡@Specification¡@
Test point 20 points (STD); 100 points ( MAX)
System Bandwidth DC-18GHz
Test Speed 0.45 sec/point
Testable PCB size 660mm x 540mm
Controller P4(or above), 2.0G
  15" LCD monitor
  40GB HDD
Printer 44 column 2 color strip printer
Weight Main unit : 160kgs
  Press down unit : 290kgs
Compressed air 5kg/cm2
Cylinder 125£p200mm
Power requirement AC source : 100/110/120V
  220V/240V, 50Hz~60Hz
  Power consumption : 700VA
Environment Temperature : 22¢J¡Ó2¢J
  Humidity : <55¡Ó5%
TDR meter Agilent 86100A-Digitizing Oscilloscope
  Agilent 54754A-Differential TDR module
  Polar-CITS 800S2
  Tektronix-TDS8200-Digital sampling Oscilloscope
  80E04-20GHz Dual-channel electrical TDR sampling module

TDR 2000I ATE

¡@ Feature¡@

  1. Marginless board testing design. Test points around board margin are testable.
  2. The precise position design is to prevent the board from injury and rebound caused by high speed transportation.
  3. This design is 60%~70% time-saving than traditional systems.
  4. Good repeatability and reproducibility.
  5. Adopting GPIB interface to connect with Tektronix, Agilent and Polar meter.
  6. Adopting 18GHz semirigid cable to fixture.
  7. Auto discharge before test to avoid damaging the meter.
  8. TDR trace parameters, such as offset, trace length and auto learning.
  9. Intranet capability and real time monitor system

¡@Dimension¡@
¡@Specification¡@
Test point 20 points (STD); 100 points ( MAX)
System Bandwidth DC-18GHz
Test Speed 0.45 sec/point
Testable PCB size min.50x100mm, max.360x400mm
Thinkness 0.5~2.0mm
Test inspection time 700pcs/hr
Machine operation time Approx. 3.5sec
Micro-Adjust
Jig Steadying 		Precision : 0.01mm
Loading section Capacity : 220PCBs (1.6mm)
Pass section Capacity :150 PCBs (1.6mm)
Fail section Capacity :150 PCBs (1.6mm)
Controller P4(or above), 2.0G
  15" LCD monitor
  40GB HDD
Printer Epson printer
Weight 600kgs
Compressed air 5kg/cm2
Power requirement AC source :
  220V/240V, 50Hz~60Hz
  Power consumption : 700VA
Environment Temperature : 22¢J¡Ó2¢J
  Humidity : <55¡Ó5%
TDR meter * Please refer to TDR 2000

TDR 2000X

¡@Feature¡@

  1. Gerber file input.
  2. Without microwave probe fixture; no test point limit.
  3. Fully programmable x, y, £c table for in circuit testing, not only coupon testing.
  4. Multi-probes structure with changeable pitch to reduce ground loop to meet short trace measurement.
  5. Fast setup! Just need several minutes to set up and help reduce error proceess and increase yield, especially for panel size pilot run.
  6. Small quantity products such as semiconductor load board or prober card testing.
  7. Fully automation with panel size load and unload mechanism. (option)
¡@Dimension¡@
¡@Specification¡@
System Bandwidth DC-18GHz
Test Speed 0.67sec/point ( Agilent 86100B)
Testable PCB size 600mm x 500mm
Z axis travel 10mm
Accuracy ¡Ó0.02mm over 300mm
Repeatability ¡Ó0.01mm
Resolution 0.01mm
Probe pressure Less than 370g
Controller Industrial PC
  15" LCD monitor
  40GB HDD
Weight 700kgs
Compressed air
 5kg/cm2
Power requirement AC source : 100/110/120V
  220V/240V, 50Hz~60Hz
  Power consumption : 700VA
Range 0~300£[
Self calibration 28£[and 50£[precision airline mounted on table for auto-calibration/verification at probe tip
 
 
Resolution 0.03£[
Environment Temperature : 22¢J¡Ó2¢J
  Humidity : <55¡Ó5%
TDR meter * Please refer to TDR 2000